63 Convertible Project [take 1]

[Lawrence]

Roger, thank you for passing along the name of the shop in Lynnwood. I tried to open up their web-page, but my browser stopped me. I will try again later from another computer, and see if I get the same results.

Anyway, as promised, below are some images of the rear 1/4 panels, which, in addition to the front driver side floor panel, require the most attention.

Kindly let me know if there are any issues with the images, and
Thank you for taking a look.
-Lawrence

[Luva65wagon]

Yes - I see the web site error here on my browser. I opened it yesterday on my phone and didn't see the error, but it is probably a warning because there seemed to be some interactive viewer thing on their site home page. I might have to contact them and suggest they might want to know that they won't get much site traffic if everyone is afraid they'll get hacked if they continue.



That's pretty typical rot on a convertible. Floors rot too on any Falcon, but floor rot usually begins from above in the dash cowl or due to a leaking windshield seal. You might want to lay on your back and look up at the sheet metal under your dash - with a bright light shining down into the vent-work from outside. You should not see any light except from inside the DS vent door and the PS heater coupling (which has probably long-since rotted away).

There is no access to the cowl through the vent-work and the drains, which are under the fenders, get clogged easily and let crud build up and rust the cowl. Even if you don't see light, that doesn't mean that if you don't clean out the crud, you won't expose the holes.

Fortunately repair panels are available for the floor and the quarters. I see them from most Falcon vendors and on ebay. Doing this sort of patch is pretty simple, but it's still hours of cha-ching at a body shop. It might be time to invest into a small MIG welder and learn how to weld - assuming you don't know how to already. So handy and so easy to learn. Floor pans are not seen, so would be a good place to learn the patching process. You can look at my Ranchero thread and see all kinds of shots of rot being cut-out and panels installed.

The cowl, if rusted - is not a fun job. Or easy. If my Ranchero rust had been simple pin-holes, I'd have just opened the ends of the cowl (where you can't see them under the fenders) and fiberglassed it or something. But mine (if you look) were way beyond that.

Anyway, all part of the "joy."

Link to my Ranchero thread. Just about every imaginable repair was done in this thread.

http://www.rainierfalcons.com/forums...ead.php?t=1482

[falcon cobra]

Hey lawrence I know a bodyman friend that could fix your quarter pannels, the shipping on those large pannels is really high, and it would cost about 800.00 each or more to install, he made the bottem of my front fenders on my 51 ford pickup and did a good job...jh

[Lawrence]

>>Roger-
I am slowly making my way through your thread. I think I got to post #36. By the looks of it, you rebuilt from the ground up! (Need a new project? -jk). The Falcon has been garaged in Edmonds for a couple of years. I'm cleaning out my garage to bring it back down to Seattle in a couple of weeks...but my space is nothing like yours.

>>JH-
It would be great to get a quote for the bodywork. Might you be able to eMail me the contact details? -->63FordFutura[at]comcast[dot]net

Thank you both,
-Lawrence

[Lawrence]

>>JH-
I forgot to ask about the bumpers on your Falcon. I don't want to jump to any conclusions, but I noticed, from your thumbnail image, they are red.

I ask become, one option (I have been thinking about) is painting fiberglass bumpers black.

Thanks again,
-Lawrence

[doghows]

If your bumpers are straight you could always powder coat them as well. We might have a club member that could do that for you.
If Rogers thread isn't enough for you check out the "Reconstruction has begun" thread on my 63 delivery.
I think I'm going to go into business with roger and start a falcon restoration shop?!?

[Luva65wagon]

I think I'm going to go into business with roger and start a falcon restoration shop?!?

When is this going to happen? Am I moving to Sequim?

[Luva65wagon]

>>Roger-
I am slowly making my way through your thread. I think I got to post #36. By the looks of it, you rebuilt from the ground up! (Need a new project? -jk). The Falcon has been garaged in Edmonds for a couple of years. I'm cleaning out my garage to bring it back down to Seattle in a couple of weeks...but my space is nothing like yours.

I'm tight. I have a lot of tools to do just about everything, but oh so wish I had a bigger garage to do it. Lot's of shuffling things around. But we make do with what we have sometimes. The Ranchero was a ground up reconstruction. I wouldn't even call it a restoration, since there was so little left I could restore on it. Similar to what you'll see on Steve (Doghows) reconstruction thread. Sometimes we just don't know better and stop. I still think back on that time period and it seems very surreal.

[doghows]

Well hopefully in the next few weeks I will be doubling the size of the powder shop.. I am way to busy and way to full need more room. Figured I might as well take the whole side of this building Im in and start flipping falcons in part and powder in the rest...
Should have about 7000 sqft or so...
Sorry for the side track, but yes your car can be saved all it takes is time and the desire to do it.. (maybe a little lack of common sense sometimes helps too)..

[Lawrence]

>>Steve-
Powder? I read about powder and powdering in Roger's thread. I need to learn more about it, as it sounds interesting. I wonder if it would work for the three chrome pieces along the top of the windshield (interior). They are small, and if memory recalls - in decent shape. But they need to be re-chromed. Perhaps powdering would give it a custom feel. Oh well, step by step.

The bumpers need some straightening. I'm headed back up to look at the car soon, so I'm making a list of things to inspect closely, take photos of, and look for.

Thanks again!